Yazar "Sabri, Mohanad Muayad Sabri" seçeneğine göre listele

Listeleniyor 1 - 5 / 5
  • Küçük Resim Yok
    Öğe
    Concrete Containing Waste Glass as an Environmentally Friendly Aggregate: A Review on Fresh and Mechanical Characteristics
    (Mdpi, 2022) Qaidi, Shaker; Najm, Hadee Mohammed; Abed, Suhad M.; Ozlahc, Yasin Onuralp; Al Dughaishi, Husam; Alosta, Moad; Sabri, Mohanad Muayad Sabri
    The safe disposal of an enormous amount of waste glass (WG) in several countries has become a severe environmental issue. In contrast, concrete production consumes a large amount of natural resources and contributes to environmental greenhouse gas emissions. It is widely known that many kinds of waste may be utilized rather than raw materials in the field of construction materials. However, for the wide use of waste in building construction, it is necessary to ensure that the characteristics of the resulting building materials are appropriate. Recycled glass waste is one of the most attractive waste materials that can be used to create sustainable concrete compounds. Therefore, researchers focus on the production of concrete and cement mortar by utilizing waste glass as an aggregate or as a pozzolanic material. In this article, the literature discussing the use of recycled glass waste in concrete as a partial or complete replacement for aggregates has been reviewed by focusing on the effect of recycled glass waste on the fresh and mechanical properties of concrete.
  • Küçük Resim Yok
    Öğe
    Effects of Waste Powder, Fine and Coarse Marble Aggregates on Concrete Compressive Strength
    (Mdpi, 2022) Basaran, Bogachan; Kalkan, Ilker; Aksoylu, Ceyhun; Ozkilic, Yasin Onuralp; Sabri, Mohanad Muayad Sabri
    The use of marble wastes in concrete mixtures, causing air and water pollution, has been promoted in the academic and practical spheres of the construction industry. Although the effects of various forms (powder, fine, coarse and mixed) of this waste on the concrete compressive strength has been subject to a decent number of studies in the literature, the difficulties in reaching specific conclusions on the effect of each test parameter constitute a major restraint for the proliferation of the use of marble wastes in the concrete industry. Most of these studies are far from underscoring all of the parameters affecting the concrete compressive strength. Due to the urgent need in the literature for comprehensive studies on concrete mixtures with marble wastes, the results of the axial compression tests on a total of 429 concrete mixtures with marble aggregates were compiled by paying special attention to reporting all test variables (form and content of marble wastes, water-cement ratio, cement content, proportion of coarse and fine aggregates in all aggregates) affecting the concrete strength. In this context, multivariate regression analyses were carried out on the existing test results. These regression analyses yielded to relationships between the change in concrete compressive strength and the test parameters for each and every form of marble waste (powder, fine and coarse aggregate). The study indicated that independent from the form of marble wastes (as powder, fine aggregate or coarse aggregate), aggregate replacements of up to 50% can yield to significant changes in the concrete compressive strength. In addition, the analytical estimates from the developed equations exhibited a high correlation (a least r value of 0.91) with the experimental results from the previous studies, yielding to rather low error values (RMSE value is 5.06 MPa at max). For this reason, the developed equations can consistently predict the changes in concrete compressive strength with varying amounts and forms of the marble aggregates as well as the other test variables.
  • Küçük Resim Yok
    Öğe
    Flexural behavior of reinforced concrete beams using waste marble powder towards application of sustainable concrete
    (Frontiers Media Sa, 2022) Karalar, Memduh; Ozkilic, Yasin Onuralp; Aksoylu, Ceyhun; Sabri, Mohanad Muayad Sabri; Beskopylny, Alexey N.; Stel'makh, Sergey A.; Shcherban, Evgenii M.
    The performance of waste marble powder as a partial replacement for cement is examined with the aim to achieve more sustainable concrete. Pursuant to this goal, a total of 15 specimens were manufactured and then tested to examine the bending behavior. The effects of longitudinal reinforcement ratio and waste marble powder ratio were selected as variables. The experimental results showed that different proportions of tension reinforcement and waste marble powder had different crack and bending impacts on reinforced concrete beams. As the waste marble powder amount in the concrete mixture is increased from 0% to 40%, it was detected that the crack type changes from a shear crack from to a flexural crack as the amount of waste marble powder increases in the mixing ratio. The experimental findings revealed that the waste marble powder can be successfully used as 10% of the partial replacement of cement. Increasing the waste marble powder ratio by more than 10% can significantly decrease the capacity of the beams, especially when longitudinal reinforcement ratio is high. The influence of waste marble as partial replacement on the capacity decreases as the longitudinal reinforcement ratio decreases. Therefore, 10%-20% marble waste can be utilized as a replacement for cement when the longitudinal reinforcement ratio is close to the balanced ratio and more than 20% waste marble ratio should be avoided for any cases.
  • Küçük Resim Yok
    Öğe
    Improvement in Bending Performance of Reinforced Concrete Beams Produced with Waste Lathe Scraps
    (Mdpi, 2022) Karalar, Memduh; Ozkilic, Yasin Onuralp; Deifalla, Ahmed Farouk; Aksoylu, Ceyhun; Arslan, Musa Hakan; Ahmad, Mahmood; Sabri, Mohanad Muayad Sabri
    In this study, the impacts of different proportions of tension reinforcement and waste lathe scraps on the failure and bending behavior of reinforced concrete beams (RCBs) are clearly detected considering empirical tests. Firstly, material strength and consistency test and then 1/2 scaled beam test have been carried out. For this purpose, a total of 12 specimens were produced in the laboratory and then tested to examine the failure mechanism under flexure. Two variables have been selected in creating text matrix. These are the longitudinal tension reinforcement ratio in beams (three different level) and volumetric ratio of waste lathe scraps (four different level: 0%, 1%, 2% and 3%). The produced simply supported beams were subjected to a two-point bending test. To prevent shear failure, sufficient stirrups have been used. Thus, a change in the bending behavior was observed during each test. With the addition of 1%, 2% and 3% waste lathe scraps, compressive strength escalated by 11.2%, 21.7% and 32.5%, respectively, compared to concrete without waste. According to slump test results, as the waste lathe scraps proportion in the concrete mixture is increased, the concrete consistency diminishes. Apart from the material tests, the following results were obtained from the tests performed on the beams. It is detected that with the addition of lathe waste, the mechanical features of beams improved. It is observed that different proportions of tension reinforcement and waste lathe scraps had different failure and bending impacts on the RCBs. While there was no significant change in stiffness and strength, ductility increased considerably with the addition of lathe waste.
  • Küçük Resim Yok
    Öğe
    Use of recycled coal bottom ash in reinforced concrete beams as replacement for aggregate
    (Frontiers Media Sa, 2022) Karalar, Memduh; Bilir, Turhan; Cavuslu, Murat; Ozkilic, Yasin Onuralp; Sabri, Mohanad Muayad Sabri
    In this research, it is studied the crack and flexural behavior of reinforced concrete beams with various bottom ash ratios (BARs) considered as fine aggregate in an experimental and numerical investigation. For experimental purposes, different concrete series are considered varying aggregate sizes ranging from 0 to 25 mm. To supplement concrete, bottom ash is put to use in conjunction with material from 0-5 mm in size aggregate particles as replacement for fine aggregates with ratios of 25%, 50%, 75%, and 100%. Experiments were done to investigate the behavior of the beams and how flexural and fracture behaviors are represented. 75% BARs gave optimum results in terms of displacement capacity. Increasing BAR to 100% decrease deflection capacity of the beam. Also, ANSYS software is used to build 3D finite element models (FEMs) of beams to compare with experiment data. Experimental and 3D numerical tests show exceptionally tight flexural and fracture behaviors. Following this, a computer-generated structure is made by running SAP 2000, and the strength of the beams is then utilised in an RC structural model. Every stage of the building's construction is thoroughly assessed utilizing multiple types of seismic testing, employing the SAP2000 program, with the resulting analysis providing significant findings on how the seismic force of 75% BAR affects horizontal displacement of each floor. The results showed that the weight of the structure dramatically decreases as the number of columns and RCBs are raised while also increasing the number of BARs. Moreover, the magnitude of earthquake and BAR have a significant effect on the horizontal displacement behavior of reinforced concrete structures. The strength of the concrete structure varies between close- and far-fault earthquakes, and for close-fault earthquakes, concrete strength is stronger than for far-fault earthquakes. This brings us to the second disadvantage of BAR which is the 75% strain produces a severe displacement of reinforced concrete structures. Besides, it was seen that the simulations and experiments yield tiny cracks with very identical configurations.